A gas burner that clicks without lighting, an induction zone that ignores the pan, a cracked ceramic hob, or a rangehood that no longer draws are kitchen jobs this referral site can take an enquiry for. Housing in Mackay covers the lot: gas cooktops in older West and South Mackay houses, ceramic and induction surfaces in newer Rural View and Ooralea kitchens, and rangehoods that work hard in the humidity and, near the coast, in salt air. Mackay Appliance Repairs does not repair or install cooktops or rangehoods. With your consent, your enquiry is passed to one independent local repair business so it can contact you, inspect the appliance and quote directly.
Note the fuel type — gas, electric ceramic, solid element or induction — and find the model number on the underside of a cooktop (often visible in the cupboard) or inside the rangehood filters.
Gas cooktops and Queensland licensing
Gas work on a cooktop, including burners, valves, igniters and the fitting of a replacement hob, must be done by a person who holds a Queensland gas work licence. If you smell gas, don't keep clicking the igniter. Turn the cooktop off at its isolation valve if you can do so safely, ventilate the kitchen, and follow Queensland gas safety advice. Ask the business that contacts you to confirm its gas work licence before any gas work starts.
A burner that will not light, lights only with a match, or burns with an uneven or yellow flame can be a blocked cap, a failed igniter or lead, a thermocouple, or a valve issue. Some of those are straightforward once a licensed worker is in the cupboard; some are not. Salt air at Bucasia, Blacks Beach, Eimeo, Shoal Point and around the harbour can corrode caps, trivets and igniter tips, so mention if the kitchen is close to the water or is often left open to the breeze.
Ceramic, solid-element and induction cooktops
Ceramic glass hobs fail in two main ways: the zone will not heat, or the glass is chipped or cracked. A zone fault can be an element, a limiter, a touch control or a board. Cracked glass is usually a replacement of the top, not a glue job, and on some models that cost sits close to a new cooktop. Don't use a cracked ceramic or induction surface; liquid in the crack is an electrical and hygiene problem.
Induction cooktops add pan detection and more electronics. A zone that will not start may be rejecting an unsuitable pan, showing an error after a spill on the controls, or dealing with a failed generator board. Try a pan you know is induction-ready and wipe the glass before you assume the zone is dead. If several zones failed at once after a storm or an outage, say so in the enquiry — surge damage to a control is a wet-season pattern in this part of Queensland.
Electric work on these cooktops should be done by a licensed electrical repairer. Built-in hobs also have to match the bench cut-out, which is worth thinking about before you jump to replacement.
Rangehoods
Rangehoods in Mackay deal with frying, humidity and, in some suburbs, a fine film of dust from the cane season. A fan that has slowed, started rattling, or stopped altogether can be a motor, a capacitor, a switch or a buildup on the impeller that the filters no longer catch. Lights and touch controls fail too. Ducted hoods suffer if the duct is crushed in the roof space or the external flap has seized; recirculating hoods depend on filters that are actually changed, not only rinsed.
A hood that no longer pulls on a still, humid evening is more than an annoyance — steam and grease end up on the cupboards and the cooktop sensors. Photos of the underside, the filters and the model sticker help the repairer know whether they are looking at a slide-out, a canopy or an integrated model over an upright cooker.
Repair or replace
Igniters, leads, switches, fan motors, filters and many control components are routinely repaired. A cracked induction or ceramic top, a gas cooktop with corroded rails and unavailable caps, or a rangehood whose motor is no longer supplied may be better replaced, especially if the bench or cabinet opening is a standard size. Ask for a figure that includes the visit and the parts, and ask who will disconnect and reconnect gas or electrical services if a replacement is the path.
Sending an enquiry
Use the form and include your suburb, the fuel type, and whether the fault is the cooktop, the rangehood or both. If you smell gas, write that clearly. Photos of the model plate, the burner or zone, and the rangehood underside help. Attendance in Walkerston, Sarina or the northern beaches depends on the repairer.
By ticking the consent box you agree that we may share your enquiry with one independent appliance repairer so they can contact you. See privacy and consent. If the oven below the cooktop is also faulty, see oven repairs, or start from the home page.
Frequently asked questions
Why does my gas cooktop keep clicking without lighting?
A wet or corroded igniter, a misaligned burner cap, a failed ignition lead or a supply issue can all cause a click with no flame. If you also smell gas, stop, isolate the cooktop if you can do so safely, and treat it as a safety issue in your enquiry rather than another attempt to light it.
Can a cracked ceramic or induction glass top be repaired?
The glass itself is not patched. On many models the top can be replaced as a part; on others the cost is close to a new cooktop. Stop using the surface and attach a photo of the crack and the model plate so the repairer can check parts.
My induction cooktop does not detect the pan. Is the zone faulty?
Try a pan that is marked induction-ready, and make sure the glass is clean and dry. If several pans fail on the same zone, or an error stays on the display, the zone or the control may need testing. Mention any recent power interruption.
Why has the rangehood fan become noisy or weak?
Grease on the impeller, clogged filters, a worn motor or a seized external flap are the usual causes. Clean or replace the filters first if you can do so safely, then enquire if the noise or the poor draw remains. Don't leave a badly vibrating hood running unattended.
Who can replace a gas cooktop in Queensland?
A licensed gas worker must disconnect and reconnect the gas. If the new cooktop also needs electrical work for ignition or a different circuit, a licensed electrical repairer may be involved as well. Ask the business to confirm both, as relevant, before the job is booked.